Download As NZS 3679.1-2010 Structural Steel Hot-Rolled Bars and Sections PDF

TitleAs NZS 3679.1-2010 Structural Steel Hot-Rolled Bars and Sections
File Size270.8 KB
Total Pages7
Table of Contents
                            AS/NZS 3679.1:2010 STRUCTURAL STEEL - HOT-ROLLED BARS AND SECTIONS
	PREFACE
	CONTENTS
	1 SCOPE
	2 NORMATIVE REFERENCES
	3 DEFINITIONS
		3.1 Analysis
			3.1.1 Cast analysis
			3.1.2 Product analysis
		3.2 Bars
		3.3 Batch
		3.4 Can
		3.5 Longitudinal direction
		3.6 May
		3.7 Off-square
		3.8 Out-of-hexagon
		3.9 Out-of-round
		3.10 Out-of-square
		3.11 Primary rolled product
		3.12 Sections
		3.13 Shall
		3.14 Should
		3.15 Testing
		3.16 Test piece
		3.17 Test sample
		3.18 Test specimen
		3.19 Transverse direction
	4 DESIGNATION
	5 STEEL MANUFACTURING PROCESS
	6 CHEMICAL COMPOSITION
		6.1 General
		6.2 Cast analysis
		6.3 Product analysis
		6.4 Residual elements
	7 MANUFACTURING TOLERANCES
		7.1 Bars
		7.2 Sections
	8 FREEDOM FROM DEFECTS
		8.1 General
		8.2 Removal of surface defects
			8.2.1 Bars
			8.2.2 Sections
		8.3 Weld repair of surface defects
			8.3.1 General
			8.3.2 Welding
	9 TESTING
		9.1 Selection of test samples
			9.1.1 General
			9.1.2 Sampling
		9.2 Position and orientation of test samples
		9.3 Preparation of test pieces for mechanical testing
			9.3.1 General
			9.3.2 Tensile test piece
			9.3.3 Impact test piece
		9.4 Testing procedures
			9.4.1 Tensile test
			9.4.2 Charpy V-notch impact test
	10 MECHANICAL PROPERTIES
		10.1 Tensile test
		10.2 Impact test
	11 IDENTIFICATION, TEST CERTIFICATES AND INDEPENDENT TESTS
		11.1 Identification
			11.1.1 Individual length markings
			11.1.2 Bundle pack markings
		11.2 Test reports and test certificate
			11.2.1 Qualifications on test reports and test certificates
			11.2.2 Minimum requirements for test certificates
		11.3 Independent tests
	12 ROUNDING OF NUMBERS
		12.1 General
		12.2 Tensile properties
	APPENDIX A - PURCHASING GUIDELINES
		A1 GENERAL
		A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
		A3 NON-DESTRUCTIVE EXAMINATION
		A4 INSPECTION
	APPENDIX B - PRODUCT CONFORMITY
		B1 SCOPE
		B2 SAMPLING AND TESTING
			B2.1 General
			B2.2 Minimum batch sampling and testing
			B2.3 Statistical sampling
	APPENDIX C - COLD-BENDING OF ROUNDS, FLATS AND SQUARES DURING FABRICATION
	APPENDIX D - DIMENSIONS
	APPENDIX E - MEASUREMENT OF CAMBER AND SWEEP IN UNIVERSAL SECTIONS
		E1 CAMBER
		E2 SWEEP
	APPENDIX F - STEEL FOR SEISMIC AND FRACTURE CRITICAL APPLICATIONS (NEW ZEALAND ONLY)
		F1 ADDITIONAL REQUIREMENTS FOR SEISMIC AND FRACTURE CRITICAL APPLICATIONS
		F2 STEEL FOR SEISMIC APPLICATIONS
		F3 STEEL FOR FRACTURE CRITICAL MEMBERS
	BIBLIOGRAPHY
                        

Similer Documents